Mesabi Metallics Company LLC safety activity
MSHA violations, accident reports and inspections.
Safety activity
Regular Safety and Health Inspection
97.5 on-site hours reported
Inspection and cover plates.
30 CFR 56.12032 · $151.00 proposed penalty
Inspection and cover plates.
30 CFR 56.12032 · $151.00 proposed penalty
Identification of power switches.
30 CFR 56.12018 · $151.00 proposed penalty
Protection of gas cylinder valves.
30 CFR 56.16006 · $151.00 proposed penalty
103 (g) Written Notification Hazard Complaint Inspectio
8.5 on-site hours reported
Berms or guardrails.
30 CFR 56.9300(a) · Significant and substantial (S&S) · $151.00 proposed penalty
Roadway maintenance.
30 CFR 56.9313 · $151.00 proposed penalty
Handtools (nonpowered)
Days away from work only
Accident narrative
EE was positioned beneath the outlet duct assisting coworker with placement of a stiffener ring onto duct. Two manual chain falls were used to maneuver the ring. Ring weighed about 1000 lbs. Each chain fall was rated for 2200 lbs. A chain fall load chain broke, causing the ring to drop. EE states they felt the stiffener ring brush their forearm before landing on their thumb.
Machinery
No dys awy frm wrk,no rstr act
Accident narrative
EE preparing to remove rigging from pad eye. EE was lowering hook using overhead crane. EE was detaching the shackle from the pad eye with gloved hands. The chain from the hoist had accumulated above the shackle and became caught on structure above pad eye. The hook from hoist rotated downward, EE's L thumb caught between the hook/housing and shackle. Contusion to thumb pad.
Slip or fall of person
All other cases (incl 1st aid)
Accident narrative
EE was moving a pallet jack loaded with iron when EE encountered a piece of 1/2 inch by 4 inch plywood covering an expansion joint on the floor. The pallet jack became stuck and as EE pulled hard to get it over the plywood, EE slipped and fell to the floor. EE also noted that there was salt and sand in the area where EE was maneuvering the iron.
Handling of materials
Dys awy frm wrk & restrctd act
Accident narrative
The injured worker states that EE has right elbow pain. Today, while adjusting the pipe bender with a coworker, EE felt/heard a "pop" in EE's right elbow. There is no appreciable bruising at this time. There is no numbness/tingling into EE's hand or fingers. There are no open wounds
Machinery
All other cases (incl 1st aid)
Accident narrative
EE in a seated position had completed grinding and set grinder down. They then placed a hand on the duct next to the grinder that had not completely stopped spinning. As they applied weight to their hand to assist in standing up. The weight caused the grinder to slide toward their hand. The spinning wheel contacted the back of left hand resulting in a burn and laceration.
Verbal Hazard Complaint Inspections
3.0 on-site hours reported
103 (g) Written Notification Hazard Complaint Inspectio
2.8 on-site hours reported
Spot Inspection
0.8 on-site hours reported
Verbal Hazard Complaint Inspections
2.8 on-site hours reported
Inspection and cover plates.
30 CFR 56.12032 · $151.00 proposed penalty
Electrical conductors.
30 CFR 56.12004 · $151.00 proposed penalty
103 (g) Written Notification Hazard Complaint Inspectio
2.8 on-site hours reported
Violation — cited standard not reported
$168.00 proposed penalty
103 (g) Written Notification Hazard Complaint Inspectio
8.3 on-site hours reported
Toilet facilities.
30 CFR 56.20008(b) · $151.00 proposed penalty
Snow and ice on walkways and travelways.
30 CFR 56.11016 · Significant and substantial (S&S) · $151.00 proposed penalty
Handtools (nonpowered)
Days away from work only
Accident narrative
Two ironworkers were working inside a cylindrical hopper at the rail pellet loading area. The task involved welding steel plate sections together as part of the hopper construction. A come along was being used to align steel plates. The come a long was attached to a welded lug. The lug broke and the come along struck the apprentice in the elbow fracturing their arm.
Sources and definitions
MSHA Violations (issue date), Accidents (accident date) and Inspections (begin date).
Violation titles use current CFR headings to identify the cited rule; they are not the inspector’s account of what happened.
Counts describe published rows, including contractor records; accident records are not distinct incidents or numbers of people injured.
Zero means no matching records in the imported sources, not proof of no events. Historical coverage differs by source; absence before a source begins reporting is not a zero incident rate. Invalid or absent dates and records after the snapshot are excluded.
S&S means SIG_SUB=Y. Fatality records use DEGREE_INJURY_CD=01. Proposed penalties are not final assessed or paid amounts; missing dollar values are omitted.
Inspection hours are SUM_TOTAL_ON_SITE_HOURS attributed to the inspection start date, without supervisor/trainee hours. Missing hours are omitted; a started inspection may still be open.
Portfolio totals use current mine membership, including events before the current owner or operator's tenure.