Cargill Deicing Solutions-Cleveland Mn safety activity
MSHA violations, accident reports and inspections.
Safety activity
Protection of power conductors from mobile equipment.
30 CFR 57.12005 · $151.00 proposed penalty
Inspection.
30 CFR 57.4201(a)(1) · $151.00 proposed penalty
Unguarded conveyors with adjacent travelways.
30 CFR 57.14109(a) · $177.00 proposed penalty
Circuit overload protection.
30 CFR 57.12001 · $151.00 proposed penalty
Operators' stations.
30 CFR 57.14103(b) · $151.00 proposed penalty
Safety defects; examination, correction and records.
30 CFR 57.14100(b) · $151.00 proposed penalty
Maximum riders in a conveyance.
30 CFR 57.19066 · $151.00 proposed penalty
Escape routes.
30 CFR 57.11051(b) · $177.00 proposed penalty
Regular Safety and Health Inspection
110.3 on-site hours reported
Immediate notification.
30 CFR 50.10(d) · $151.00 proposed penalty
Special Emphasis Programs
1.3 on-site hours reported
Fire
Accident only
Accident narrative
An employee observed an electrician's golf cart that was parked near the Phoist control room was on fire and notified their supervisor. The supervisor contacted CFD and verified that the EVAC system was activated. The supervisor immediately traveled to the location of the golf cart and found that the fire had been extinguished by employees using fire extinguishers.
Hoisting
Accident only
Accident narrative
Lost use of PHoist due to drive fault/bad module caused by high moisture.
Hoisting
Accident only
Accident narrative
Lost operation of the PHoist due to a failed drive module
Machinery
Accident only
Accident narrative
At approximately 10:30 PM, the number one main fan went down due to mechanical issues. Based on the inspection, it appears the impellers came off, the bearing locked up and it went high amps/temp.
Hoisting
Accident only
Accident narrative
During hoist checks, the tanks for the pneumatic system did not refill. Issue could not be resolved within allotted time frame, so EVAC was called. Cause of issue was found to be a rubber gasket from the oiler blew out and lodged itself in the #2 pneumatic valve.
Handtools (nonpowered)
Days restricted activity only
Accident narrative
An employee was cutting a zip tie off of a D-ring when the knife slipped and sliced the inside of EE's left forearm. The laceration was approximately 1" in length and required 3 stitches. The employee was permitted to return to work with instructions to keep the wound covered. This incident did not result in any lost time.
Construction and maintenance of ladders.
30 CFR 57.11003 · $151.00 proposed penalty
Safety defects; examination, correction and records.
30 CFR 57.14100(b) · $151.00 proposed penalty
Identification of power switches.
30 CFR 57.12018 · $151.00 proposed penalty
Inspection.
30 CFR 57.4201(a)(2) · $151.00 proposed penalty
Check-in, check-out system.
30 CFR 57.11058 · $151.00 proposed penalty
Guarding electrical connections and resistor grids.
30 CFR 57.12023 · $151.00 proposed penalty
Inspection and cover plates.
30 CFR 57.12032 · $151.00 proposed penalty
Electrical conductors.
30 CFR 57.12004 · $151.00 proposed penalty
Sources and definitions
MSHA Violations (issue date), Accidents (accident date) and Inspections (begin date).
Violation titles use current CFR headings to identify the cited rule; they are not the inspector’s account of what happened.
Counts describe published rows, including contractor records; accident records are not distinct incidents or numbers of people injured.
Zero means no matching records in the imported sources, not proof of no events. Historical coverage differs by source; absence before a source begins reporting is not a zero incident rate. Invalid or absent dates and records after the snapshot are excluded.
S&S means SIG_SUB=Y. Fatality records use DEGREE_INJURY_CD=01. Proposed penalties are not final assessed or paid amounts; missing dollar values are omitted.
Inspection hours are SUM_TOTAL_ON_SITE_HOURS attributed to the inspection start date, without supervisor/trainee hours. Missing hours are omitted; a started inspection may still be open.
Portfolio totals use current mine membership, including events before the current owner or operator's tenure.